IMT
Classic 45 ATC
CLASSIC 45 ATC
C LASSIC
Included equipment:
Frequency converter, cable, collets
PRODUCT DESCRIPTION
Max. power output 1.1 kW
Power output S6 40% 0.60 kW at 36.000 min-1
Power output S1 100% 0.45 kW at 36.000 min-1
Rotation speed to 60.000 rpm
Square housing Ø 45 / 69 x 69 mm
Spindle housing Aluminium
Spindle interface Pneumatic Collet
MADE IN GERMANY
C LASSIC
Included equipment:
Frequency converter, cable, collets
PRODUCT DESCRIPTION
Max. power output 1.1 kW
Power output S6 40% 0.60 kW at 36.000 min-1
Power output S1 100% 0.45 kW at 36.000 min-1
Rotation speed to 60.000 rpm
Square housing Ø 45 / 69 x 69 mm
Spindle housing Aluminium
Spindle interface Pneumatic Collet
MADE IN GERMANY
Motor Data
Motor type: asynchron
Number of pol´s: 2
Speed range (rpm) max: 60.000
Power output
S1/S6 40% (kW)
0.45 / 0.60
Torque S1/S6 40% (Nm)
0.12 / 0.16
Frequency range (Hz) max.
1000
Max. voltage (Volt)
210
Nominal current
S1/S6 40% (Amp.)
2.5 / 3.5
Maximum current (Amp.): 6
Motor type: asynchron
Number of pol´s: 2
Speed range (rpm) max: 60.000
Power output
S1/S6 40% (kW)
0.45 / 0.60
Torque S1/S6 40% (Nm)
0.12 / 0.16
Frequency range (Hz) max.
1000
Max. voltage (Volt)
210
Nominal current
S1/S6 40% (Amp.)
2.5 / 3.5
Maximum current (Amp.): 6
Bearing Data
Bearings, Hybrid - Ceramic
Number of bearings / Ø (mm) 3 / 15
Lubrication: Grease
Temperature protection ü
Recommended air seal (bar) 1 - 2
Air seal requirements (l/min) 80
Bearings, Hybrid - Ceramic
Number of bearings / Ø (mm) 3 / 15
Lubrication: Grease
Temperature protection ü
Recommended air seal (bar) 1 - 2
Air seal requirements (l/min) 80
Tooling
Spindle interface 7
Clamping torque Ø 3mm (Nm)
Tool clamping / release pressure (bar)
Max. Tool diameter (mm): 3
Requires comp. air at 3 bars for opening of collet - Requires Air Source (Air Source Not Supplied by Minitech)
Spindle interface 7
Clamping torque Ø 3mm (Nm)
Tool clamping / release pressure (bar)
Max. Tool diameter (mm): 3
Requires comp. air at 3 bars for opening of collet - Requires Air Source (Air Source Not Supplied by Minitech)
Shaft Data
Run-out accuracy: – Axial eccentricity (μm) < 1
Spindle taper (μm) < 2
Balance quality G 0.4
Vibration (mm/s) < 1
Static axial stiffness (N/μm) 13
Static radial stiffness (N/μm) 22
Run-out accuracy: – Axial eccentricity (μm) < 1
Spindle taper (μm) < 2
Balance quality G 0.4
Vibration (mm/s) < 1
Static axial stiffness (N/μm) 13
Static radial stiffness (N/μm) 22
Air Regulator
The AL-C1204 Regulates and cleans compressed air source for cooling the spindle bearings. It is an ultra-clean air supply unit. Dust and moisture in the compressed air are eliminated by the 0.3 micron filter in the first stage and regulator provides accurate and stable air to the control unit.
Included in Air Line Kit:
• Air Filter - filter mesh 0.3 µm
• Air Regulator
• Air Pressure Gauge
• Air ON-OFF Valve
• Hose for piping (K-275): Ø8mm dia. x 6 ft
• For use with Ø6mm hose
• REQUIRES compressed air at 1.0CFM (36-44PSI)
The AL-C1204 Regulates and cleans compressed air source for cooling the spindle bearings. It is an ultra-clean air supply unit. Dust and moisture in the compressed air are eliminated by the 0.3 micron filter in the first stage and regulator provides accurate and stable air to the control unit.
Included in Air Line Kit:
• Air Filter - filter mesh 0.3 µm
• Air Regulator
• Air Pressure Gauge
• Air ON-OFF Valve
• Hose for piping (K-275): Ø8mm dia. x 6 ft
• For use with Ø6mm hose
• REQUIRES compressed air at 1.0CFM (36-44PSI)
